HP2-Z37 Online Practice Questions and Answers

Match the description with the 802.11 standard. (Each option may be used only once.)

Hot Area:

A company wants a modular switch for the access layer at its main campus and for several branch offices. Which HP Switch Series is best suited for this role?

A. HP 11900

B. HP 12900

C. HP 5900

D. HP 5400R

Refer to the exhibit.

Based on the topology shown in the exhibit, which symptom does a network administrator see if the HP switches are in their factory default states?

A. Mislearned MAC addresses

B. Unicast storms

C. Multiple ARP requests

D. Layer 3 loop

What is true about the community string used for SNMPv1 and SNMPv2c?

A. The community string encrypts the SNMP message, but does not hash it, providing for data privacy.

B. The community string hashes the SNMP message, but does not encrypt it, providing for data integrity.

C. The community string encrypts and hashes the SNMP message, providing for data integrity and privacy.

D. The community string is like a password transmitted in cleartext, providing no data integrity or privacy.

Refer to the exhibit.

The switches in the exhibit are all HP Comware switches that run Multiple Spanning Tree Protocol (MSTP).

The network administrator wants to ensure that each switch-to-switch link is in its own subnet. The administrator also wants to make sure that all of the links are available for routing during normal operation. How should the administrator configure the physical switch-to-switch interfaces to accomplish these goals?

A. Configure them as trunk ports that permit VLANs 10 and 20.

B. Configure them as any type of port, and make sure spanning tree is enabled on them.

C. Configure them as route-mode ports.

D. Configure them as hybrid ports that carry VLAN 10 and 20 as untagged.

Refer to the exhibit.

A network administrator enters the command shown in the exhibit to check the VLANs on an HP ProVision switch interface. The administrator wants to discover which VLANs are tagged and untagged on the port. What can the administrator do to accomplish this?

A. Enter the show vlans ports 1 command but add detail at the end of the command.

B. View all VLANs on the switch by entering the show vlans command without a VLAN ID.

C. View the physical interface by entering the show interface brief command.

D. Enter the show interfaces all command.

A network administrator executes these commands on an HP ProVision switch: ProVision(config)# ip route 10.1.100.0/24 10.1.1.1 ProVision(config)# ip route 10.1.200.0/24 10.1.1.1 The administrator attempts to ping a device in the 10.1.100.0/24 network from a client attached to the switch and is unable to ping it. Assume there are no firewalls and all other settings are correct. What must the administrator configure on

the ProVision switch to get a response?

A. ProVision(config)# ip routing

B. ProVision(config)# spanning-tree disable

C. ProVision(config)# routing enable

D. ProVision(config)# routingProVision(config-router)# ip enable

An HP ProVision switch is operating at its factory default settings. A network administrator connects the switch to a VLAN with a DHCP server. The switch-to-switch connection is carrying untagged traffic. The administrator wants to log in to the switch CLI using Telnet.

How should the administrator contact the switch and log in?

A. Contact the switch at its DHCP-assigned IP address and log in with the default password hp.

B. Contact the switch at its default IP address 192.168.1.1/24 and log in without entering a password.

C. Contact the switch at its DHCP-assigned IP address and log in without entering a password.

D. Contact the switch at its default IP address 192.168.1.1/24 and log in with the default password hp.

A customer is implementing a network using HP ProVision switches. Which default setting applies to the ProVision switches?

A. All ports are disabled.

B. Routing is enabled.

C. Telnet is enabled.

D. A static IP address is assigned to VLAN 1.

A mid-sized company purchases HP Intelligent Management (IMC) to manage 500 nodes. In addition to the base platform, the company purchases the UAM, WSM, and NTA modules. Which deployment method should this company use to install their IMC base platform and modules?

A. Stand-alone

B. Distributed

C. Centralized

D. Hierarchical