DCPPE-200 Online Practice Questions and Answers

An engineer needs to re-purpose the storage of the chassis. Data must NOT be lost when a drive fails. The configuration needs to allow for redundancy with the maximum amount of usable space.

What should the engineer create to perform this task?

A. RAID 60

B. RAID 50

C. RAID 5

D. RAID 6

An engineer is deploying a chassis with four IOAs and connecting it to the top of rack (ToR) switch. The deployment mandate requires that the switches be presented as one logical unit. Future servers can be added to network with the minimal amount of configuration.

The following steps have been completed:

-IOAs are daisy-chained using ports 9 and 10

-Cabled ports 11 and 12 on IOA 1 to the ToR

-

Configured a team on NIC ports 1 and 2 on the server How should the IOMs be configured?

A.

Virtual Link Trunking

B.

Stack

C.

FullSwitch

D.

Programmable MUX

An engineer installs a second Shared PERC Internal card into a VRTX and is performing post installation

tasks.

The Fault Tolerant Status is NOT Healthy/Normal as expected.

What is the cause?

A. The VRTX wasNOTlicensed for two Shared PERC Internal cards.

B. The physical disks were removed from the chassis before initialization finished.

C. The Shared PERC cards areNOTat the same firmware level.

D. One or more nodes are still assigned virtual disks.

A customer has five VRTXs in a chassis group that they need to disband. The engineer disbands the chassis group from the group leader, but a networking interruption prevents two of the VRTXs from getting the signal to leave the group.

What should the engineer do to finish disbanding the chassis group?

A. Remove the remaining members from the group leader's Remove Members list

B. Recreate the group fromthe group leader and disband it again

C. Remove the group association from the group members individually

D. Reboot the CMCs of the remaining members

An engineer needs to configure network port partitions for four networks that will be used on the server.

-

Partition 1 – Management network

-

Partition 2 – VM Live Migration network

-

Partition 3 – Production VM network

-

Partition 4 – Development VM network

The engineer needs to make sure the following conditions are met:

-Management and Live Migration networks do NOT exceed 1Gb

-Production VM network can use 10Gb but is guaranteed 5Gb during heavy use

-

Development VM network has maximum bandwidth capability when NOT in use by the other networks Which network port partition bandwidth settings should the engineer set?

A.

Partition 1 Partition 2 Partition 3 Partition 4 Relative Bandwidth Weight 0094Maximum Bandwidth1153

B.

Partition 1 Partition 2 Partition 3 Partition 4 Relative Bandwidth Weight 1153Maximum Bandwidth111010

C.

Partition 1 Partition 2 Partition3 Partition 4 Relative Bandwidth Weight 009040Maximum Bandwidth1010100100

D.

Partition 1 Partition 2 Partition 3 Partition 4 Relative Bandwidth Weight 1010 50 30 Maximum Bandwidth 1010 100 100

AN engineer needs server 1 in the chassis to be able to communicate on the default untagged VLAN 1 and tagged VLANs 10, 20, and 50. The engineer has port 1 configured with the following settings:

interface TenGigabitEthernet 0/1 mtu 12000 switchport vlan tagged 10,20,50 flowcontrol rx on tx off During testing, the engineer is unable to communicate with anything on VLAN 1. How should the engineer fix this issue?

A. Set the MTU to default of 1500

B. Change the default untagged VLAN and tag VLAN 1

C. Disable all flowcontrol

D. Configure port 1 as a hybrid port

An engineer is configuring a new FD332 storage sled into an existing chassis in SLOT 3. The FD332 is NOT being detected by the assigned node.

Which two tasks must an engineer complete so that the FD332 is detected by the node? (Choose two.)

A. Verify firmware is up to date

B. Reseat the FD332

C. Import the PERC license

D. Enable the PERC instorage sled

E. Power cycle the node

An engineer enters a data center to configure an uplink between an I/O Aggregator (IOA) and an upstream switch. The IOA and upstream switch are configured for spanning tree. The engineer applies the following configuration to the uplink port:

interface TenGigabitEthernet 0/12 switchport flowcontrol rx on tx off spanning-tree rstp edge-port As soon as the engineer plugs in the cables, it creates a loop and brings down the network. Which commands should be entered on the IOA to fix loop?

A. interface TenGigabitEthernet 0/12no spanning-tree rstp edge-port

B. spanning-tree protocol rstpbridge priority 32768

C. interface TenGigabitEthernet 0/12spanning tree loop detect

D. spanning-tree protocol rstpbridge priority 0

A password to the CMC root account on an M1000e server chassis has been misplaced. What should be done to restore administrative access to the CMC?

A. Reset root password using the PASSWORD_RSET jumper

B. Issue password reset from a connected blade's iDRAC

C. Call Dell tech support and ask to reset CMC password via SupportAssist

D. Access CMC through serial console and issue theenable secretcommand

An engineer needs to put chassis switches on a LAN that has already been configured for latency sensitive applications and to enable lossless links.

How should the engineer accomplish this?

A. iscsi enable

B. dcd-input pfc

C. flowcontrol rx on tx off

D. enable perf enhance